Resumo em Inglês:

The aim of the present study was to evaluate the tensile strength, elongation, microhardness, microstructure and fracture pattern of various metal ceramic alloys cast under different casting conditions. Two Ni-Cr alloys, Co-Cr and Pd-Ag were used. The casting conditions were as follows: electromagnetic induction under argon atmosphere, vacuum, using blowtorch without atmosphere control. For each condition, 16 specimens, each measuring 25 mm long and 2.5 mm in diameter, were obtained. Ultimate tensile strength (UTS) and elongation (EL) tests were performed using a Kratos machine. Vickers Microhardness (VM), fracture mode and microstructure were analyzed by SEM. UTS, EL and VM data were statistically analyzed using ANOVA. For UTS, alloy composition had a direct influence on casting condition of alloys (Wiron 99 and Remanium CD), with higher values shown when cast with Flame/Air (p < 0.05). The factors 'alloy" and 'casting condition" influenced the EL and VM results, generally presenting opposite results, i.e., alloy with high elongation value had lower hardness (Wiron 99), and casting condition with the lowest EL values had the highest VM values (blowtorch). Both factors had significant influence on the properties evaluated, and prosthetic laboratories should select the appropriate casting method for each alloy composition to obtain the desired property.

Resumo em Inglês:

The aim of this study was to verify the influence of the time of contact between alginate and gypsum after the modeling procedure on the properties of the plaster cast, such as surface detail, dimensional stability and microhardness. Thirty cylindrical specimens of orthodontic gypsum Type III were made by means of impressions of a stainless steel master model which had five reference lines in the upper surface. The samples were divided into two groups: Group 1 (G1) - with time of contact of 1 hour; and Group 2 (G2) - 12 hours of contact. All the specimens were stored up to 48 hours until they underwent laboratory testing. Surface detail and dimensional stability were tested by one calibrated examiner using a visual analysis and a profilometer (Profile Projector Nikon model 6C, Nikon Corporation, Tokyo, Japan), respectively, to evaluate the quality of reproduction of the lines and the distances between them. The microhardness was determined for each sample by making six indentations with a Vickers diamond pyramid indenter (Buehler, Lake Bluff, USA) under a load of 100 gF for 15 s. The results showed significant difference (P £ 0.05) between groups in two of the three properties examined: surface detail and microhardness, which decreased as the time of contact rose. The 12-hour time of contact between alginate and the plaster cast is not recommended because it influences the quality of the plaster cast.

Resumo em Inglês:

We compared polymerization stress in two commercial composites and three experimental composites made using camphorquinone (CQ) and/or phenylpropanedione (PPD) as photoinitiators. The internal surfaces of photoelastic resin discs with cylindrical cavities were roughened and treated with adhesive. Composites were divided into five groups: two commercial composites (Filtek Silorane and Filtek Z250) and three experimental composites with CQ/amine, CQ/PPD/amine, and PPD/amine. Composites were photopolymerized inside cavities, and subjected to photoelastic analysis immediately and at 24 hours and 7 days later using a plane polariscope. Stress created by Silorane (3.08 ± 0.09 MPa) was similar to that of Z250 (3.19 ± 0.13 MPa) immediately after photopolymerization (p > 0.05). After 24 hours and 7 days, Z250 (3.53 ± 0.15 and 3.69 ± 0.10 MPa, respectively) showed higher stress than Silorane (3.19 ± 0.10 and 3.16 ± 0.10 MPa, respectively). Qualitative analysis immediately after photopolymerization showed composite/CQ promoted higher stress than PPD, but stress levels at other evaluated times were statistically similar, varying between 3.45 ± 0.11 MPa and 3.92 ± 0.13 MPa. At 24 hours and 7 days, Silorane created the lowest stress. All photoinitiators created comparable tensions during polymerization.

Resumo em Inglês:

The aim of this study was to determine the influence of mouthrinses on the surface roughness of a nanofilled composite resin after toothbrushing. One hundred nanofilled composite resin specimens were prepared and randomly distributed into two groups-brushed and non-brushed-and then assigned to five subgroups, according to the mouthrinse solutions (n = 10): Colgate Plax Fresh Mint, Oral B, Cepacol, Colgate Plax, and artificial saliva. Each sample was immersed in 20 mL of the mouthrinses for 1 minute, 5 days per week, twice a day, for a 3-week period. The control group used in the study was one in which the specimens were not subjected to brushing and remained only in artificial saliva. Toothbrushing was performed once a week for 1 minute, for 3 weeks. Surface roughness measurements (Ra) were performed after the immersion period and toothbrushing, by means of a profilometer. Data were analyzed by two-way ANOVA and Tukey's test. Analysis revealed that the association between toothbrushing and Colgate Plax Fresh Mint produced the lowest surface roughness (p < 0.05). All other groups tested (Oral B, Cepacol, Colgate Plax, artificial saliva) exhibited no statistically significant differences between surfaces, whether subjected to toothbrushing or not (p < 0.05). It was concluded that the surface roughness of the nanofilled composite resin tested can be influenced by the mouthrinse associated with toothbrushing.

Resumo em Inglês:

This in vitro study evaluated both the antimicrobial activity and the root canal cleaning ability of plant extracts used in irrigation solutions. The antimicrobial activities of the aroeira-da-praia (Schinus terebintifolius Raddi) and the quixabeira (Syderoxylum obtusifolium Roem & Schult) hydroalcoholic extracts, of 2.5% sodium hypochlorite (NaOCl) and of 0.12% chlorhexidine (positive control) against Enterococcus faecalis were tested with the agar well diffusion method. The level of root canal cleanliness was examined by scanning electron microscopy (SEM). Twenty one single-rooted human teeth were divided into three groups according to the irrigation solution applied: 1) 50% aroeira-da-praia; 2) 50% quixabeira and 3) a combination of 2.5% sodium hypochlorite + 17% EDTA. All solutions tested demonstrated antimicrobial activity against Enterococcus faecalis. The SEM analysis revealed that higher and lower degrees of surface cleaning were observed, in the three groups, respectively for the coronal and apical thirds, in that quixabeira showed the greatest efficiency in removing the smear layer in the apical third. All the agents tested presented antimicrobial activity against E. faecalis. None, however, was able to completely remove the smear layer of the dentinal surface in the different thirds of the root canal. The results suggest that the analyzed plant extracts may represent a new therapeutic option in the list of alternative agents available for endodontic treatment.

Resumo em Inglês:

The aim of this study was to compare two methods of assessing apical transportation in curved canals after rotary instrumentation, namely, cross-sections and micro-computed tomography (µCT). Thirty mandibular molars were divided into two groups and prepared according to the requirements of each method. In G1 (cross-sections), teeth were embedded in resin blocks and sectioned at 2.0, 3.5, and 5.0 mm from the anatomic apex. Pre- and postoperative sections were photographed and analyzed. In G2 (µCT), teeth were embedded in a rubber-base impression material and scanned before and after instrumentation. Mesiobuccal canals were instrumented with the Twisted File (TF) system (SybronEndo, Orange, USA), and mesiolingual canals, with the EndoSequence (ES) system (Brasseler, Savannah, USA). Images were reconstructed, and sections corresponding to distances 2.0, 3.5, and 5.0 mm from the anatomic apex were selected for comparison. Data were analyzed using Mann-Whitney's test at a 5% significance level. The TF and ES instruments produced little deviation from the root canal center, with no statistical difference between them (P > 0.05). The canal transportation results were significantly lower (0.056 mm) in G2 than in G1 (0.089 mm) (p = 0.0012). The µCT method was superior to the cross-section method, especially in view of its ability to preserve specimens and provide results that are more closely related to clinical situations.

Resumo em Inglês:

Oral cancer is commonly preceded by premalignant lesions and conditions. The clinician's ability to identify lesions at an increased risk of cancer development is critical for its control. The purpose of this study was to compare the expression of tumor suppressor gene p53, proliferation marker Ki-67, and oncogene c-erbB2 and to evaluate the relevance of their co-expression in the diagnosis of, and prognosis for, oral leukoplakia. In the present study, the expression of biomarkers was studied immunohistochemically in 55 cases of leukoplakia (26 without dysplasia, 29 with dysplasia) and 10 cases of normal epithelia. The Labeling Indices (LI) of p53 and Ki-67 were found to increase significantly with an increase in the grade of dysplasia. A significant correlation was also found between the LI of p53 and that of Ki-67. It was also observed that c-erbB2 expression was only cytoplasmic, indicating incomplete receptor degradation. Hence, it can be concluded from the present study that the increased expression of p53 and Ki-67 with an increase in the grade of dysplasia suggests that their co-expression may be used for the identification of high-risk lesions. Also, c-erbB2 has no pathogenetic role in early carcinogenesis in the studied population, although incomplete receptor degradation, as evidenced by cytoplasmic staining, may indicate an early change.

Resumo em Inglês:

The purpose of the present paper was to describe the range of lesions histologically diagnosed in an oral pathology laboratory in southern Brazil. A retrospective study of 8,168 specimen analyses recorded between 1995 and 2004 was conducted. The records were retrieved from the Oral Pathology Laboratory, School of Dentistry, Federal University of Rio Grande do Sul, RS, Brazil. A total of 6,831 valid cases (83.63%) were examined. Of these, inflammatory lesions were the most common occurrences (n = 4,320; 63.24%). Benign and malignant tumors accounted for 7.66% (n = 523) and 1.9% (n = 130) of the occurrences, respectively. Significant associations were observed between nonneoplastic proliferative disorders and benign mesenchymal tumors in females, and between squamous cell carcinoma and leukoplakia in males. Most diagnoses were benign in nature and had an inflammatory etiology. The association of some demographic characteristics with the occurrence of lesions suggests that these characteristics should be considered in performing differential diagnoses.

Resumo em Inglês:

This study analyzed occlusal radiographs to compare the transverse changes produced in patients treated with rapid maxillary expansion using two types of appliances. The sample consisted of 31 children aged 7 to 10.6 years, of both genders, with posterior cross-bite. Fifteen children were treated with a tooth-borne expander and 16 were treated with a tooth-tissue-borne expander. Occlusal radiographs obtained at treatment onset and at the end of the retention period were digitized. The following variables were measured: intermolar distance (IMD), interapical distance (IApD), interbase distance (IBaD) and interarm distance (IArD). The results revealed increases in all measurements in both groups after rapid maxillary expansion. Comparison between groups revealed that the increases were greater in patients treated with the tooth-borne expander, except for the IArD measurement, which presented the same increase in both groups. Even though the IMD measurements differed between expanders, they were proportional to the activation of the appliances (IBaD). The increase in the IApD measurement was proportionally greater in the group treated with the tooth-borne expander (0.7:1.0) than in that treated with the tooth-tissue-borne expander (0.4:1.0). It was concluded that both appliances had similar effects, although the tooth-tissue-borne expander produced a lesser opening at the apical region of the incisors.

Resumo em Inglês:

We evaluated the influence of photoactivation method and hydrophobic resin (HR) application on the marginal and internal adaptation, hardness (KHN), and crosslink density (CLD) of a resin-based fissure sealant. Model fissures were created in bovine enamel fragments (n = 10) and sealed using one of the following protocols: no adhesive system + photoactivation of the sealant using continuous light (CL), no adhesive system + photoactivation of the sealant using the soft-start method (SS), HR + CL, or HR + SS. Marginal and internal gaps and KHN were assessed after storage in water for 24 h. The CLD was indirectly assessed by repeating the KHN measurement after 24 h of immersion in 100% ethanol. There was no difference among the samples with regard to marginal or internal adaptation. The KHN and CLD were similar for samples cured using either photoactivation method. Use of a hydrophobic resin prior to placement of fissure sealants and curing the sealant using the soft-start method may not provide any positive influence on integrity or crosslink density.

Resumo em Inglês:

The aim of this study was to conduct an in vitro evaluation, by scanning electron microscopy (SEM), of the adhesion of blood components on root surfaces irradiated with Er,Cr:YSGG (2.78 µm) or Er:YAG (2.94 µm) laser, and of the irradiation effects on root surface morphology. Sixty samples of human teeth were previously scaled with manual instruments and divided into three groups of 20 samples each: G1 (control group) - no treatment; G2 - Er,Cr:YSGG laser irradiation; G3 - Er:YAG laser irradiation. After performing these treatments, blood tissue was applied to 10 samples of each group, whereas 10 samples received no blood tissue application. After performing the laboratory treatments, the samples were observed under SEM, and the resulting photomicrographs were classified according to a blood component adhesion scoring system and root morphology. The results were analyzed statistically (Kruskall-Wallis and Mann Whitney tests, α= 5%). The root surfaces irradiated with Er:YAG and Er,Cr:YSGG lasers presented greater roughness than those in the control group. Regarding blood component adhesion, the results showed a lower degree of adhesion in G2 than in G1 and G3 (G1 × G2: p = 0.002; G3 × G2: p = 0.017). The Er:YAG and Er,Cr:YSGG laser treatments caused more extensive root surface changes. The Er:YAG laser treatment promoted a greater degree of blood component adhesion to root surfaces, compared to the Er,Cr:YSGG treatment.

Resumo em Inglês:

The aim of this randomized, controlled, split-mouth, clinical study was to differentiate and clinically qualify the effectiveness of different desensitizing agents in the treatment of painful symptoms caused by cervical dentin hypersensitivity (CDH). Two hundred-and-fifty-two teeth of 42 patients were distributed into seven groups (n = 36): G1 - placebo; G2, G3, G4 and G6 - fluoride varnishes; G5 - sodium fluoride; G7 - potassium oxalate. Three applications were made one week apart. A three-score system (Alfa = 0, Bravo = 2, and Charlie = 3, respectively for no sensitivity, slight sensitivity and high sensitivity) was used to assess CDH after each application and after 30 days. The data were subjected to statistical analysis using the Kruskall-Wallis and Dun tests. After the second week, statistically significant differences were observed for all materials compared with the baseline. After 30 days, Group G7 had presented a significant gradual reduction along all the evaluated time intervals. It was concluded that all the desensitizing agents were capable of reducing dentin hypersensitivity, with the exception of the placebo and the sodium fluoride groups.

Resumo em Inglês:

The aim of this study was to evaluate the bleaching effect of two mouth rinses containing hydrogen peroxide. Thirty premolars were randomly divided into two groups (n = 15): Listerine Whitening (LW) and Colgate Plax Whitening (PW). The teeth were fixed on a wax plate and with acrylic resin, at a distance of 5 mm between each other, exposing the buccal surfaces. All teeth were stored in artificial saliva for 45 days, being removed twice a day to be immersed for 1 min in each mouthwash, followed by 10-second washing in tap water. The pH of each product was measured. Digital images of each tooth were captured under standardized conditions. These images were cut in areas previously demarcated and analyzed in Adobe Photoshop 7.0 using the CIEL*a*b* color space system. Data were statistically analyzed by a paired t test and an independent samples t test (p < 0.05). The pH values were 5.6 and 3.4 for LW and PW, respectively. Both treatment groups showed a decrease in the b* parameter (p < 0.01), but a decrease of a* was observed only for PW (p < 0.01). While the LW group showed an improvement in lightness (L*) (p = 0.03), the PW group had a decrease in the L* parameter (p = 0.02). Within the limitations of this study, it is possible to conclude that both products caused some degree of whitening; however, extreme care should be taken when using Colgate Plax Whitening, since its decline in luminosity might be due to its lower pH.

Resumo em Inglês:

The aim of the present study was to evaluate the fracture resistance of teeth restored with resin composite. Forty-eight maxillary premolar teeth were chosen and randomly divided to six groups: G1 (control): sound teeth; G2: MOD preparation, unrestored; G3: MOD + Adper Single Bond 2/P60; G4: MOD + Adper Easy One/P60; G5: MOD + P90 restorative system; G6: MOD + Adper Easy One/P90 Bond/P90. Specimens were subjected to compressive axial loading (0.5 mm/min). Flexural strength and the modulus of elasticity were also tested (n = 7). The only statistical equivalence with sound teeth was noted for G3 (p < 0.05). Flexural strength and the modulus of elasticity varied among the composites tested (n = 10). The reestablishment of the resistance to fracture in premolars subjected to Class II MOD preparations is restorative-system-dependent. The silorane restorative system is not able to recover the resistance to fracture.

Resumo em Inglês:

This study evaluated the influence of solvent evaporation conditions of acid-etching adhesives. The medium dentin of thirty extracted human third molars was exposed and bonded to different types of etch-and-rinse adhesives: 1) Scotchbond Multi-Purpose (SBMP) ; water-based; 2) Adper Single Bond 2 (SB) ; ethanol/water-based, and 3) Prime & Bond 2.1 (PB) ; acetone-based. Solvents were evaporated at air-drying temperatures of 21ºC or 38ºC. Composite buildups were incrementally constructed. After storage in water for 24 h at 37ºC, the specimens were prepared for bond strength testing. Data were analyzed by two-way ANOVA and Tukey's test (5%). SBMP performed better when the solvents were evaporated at a higher temperature (p < 0.05). Higher temperatures did not affect the performance of SB or PB. Bond strength at room temperature was material-dependent, and air-drying temperatures affected bonding of the water-based, acid-etching adhesive.