A study of Pr-Fe-B magnets produced by a low-cost powder method and the hydrogen decrepitation process

A study of Pr-Fe-B magnets produced by a low-cost powder method and the hydrogen decrepitation process

Edson Pereira Soares^I; Élio Alberto Périgo^I; Hidetoshi Takiishi^I; Claudio Costa Motta^II; Rubens Nunes Faria^I,*

^IInstituto de Pesquisas Energéticas e Nucleares, IPEN-CNEN, 05422-970 São Paulo, Brazil

^IICentro Tecnológico da Marinha em São Paulo, CTMSP, São Paulo, Brazil

ABSTRACT

Sintered Pr-based magnets were produced using a new laboratory technique for powder handling. Unlike the conventional procedure for preparing sintered permanent magnets in the laboratory, the powder technique used in this investigation does not require a glove box. The effects of processing parameters on the magnetic properties of Pr-based sintered magnets prepared using the hydrogen decrepitation process have been studied. Specifically, the effects of sintering temperature and milling time for processing Pr₁₆Fe₇₆B₈ magnets have been investigated. Pr₁₆Fe₇₆B₈ magnets with the best magnetic properties were sintered between 1015 °C to 1075 °C.

Keywords: Pr-alloys, magnetic materials, hydrides, magnetic properties

1. Introduction

The powder transfer technique developed recently in this laboratory was quite satisfactory for preparing neodymium-based sintered magnets¹. Hydrogen decrepitated (HD) sintered magnets produced using this new technique exhibited magnetic behavior similar to magnets prepared using standard procedures^2,3. Furthermore, the magnetic properties of the sintered magnets prepared by this low-cost method were equivalent to those of commercial magnets with identical composition⁴. The Pr-based magnets studied previously used the hydrogen decrepitation process followed by roll milling and the powder was handled in a glove box with less than 30 ppm oxygen^5-11. In this investigation, this new technique has been used for producing praseodymium-based magnets in the laboratory without a glove box. Hydrogen decrepitated Pr₁₆Fe₇₆B₈ sintered magnets were produced by this low-cost technique using various milling times. The optimum sintering temperature for this material has also been determined. Hydrogen decrepitated Pr₁₇Fe₇₉B₄ sintered magnets have been included in this work for comparison.

2. Experimental Procedure

Commercially available Pr₁₆Fe₇₆B₈ and Pr₁₇Fe₇₉B₄ alloys were processed in the as-received condition, that is, in the conventional cast ingot state. To prepare Pr-type magnets via the HD process, the following procedure was used^5-8. Small pieces of the bulk ingot were placed in a stainless steel hydrogenation vessel that was then evacuated to backing-pump pressure. Hydrogen was introduced to a pressure of 1 bar, which resulted in decrepitation of the bulk material. This material was then transferred to a ball milling container which was filled with cyclohexane and roll milled for several hours (9-36 hours). The milling container was then coupled to the transfer system¹. Figure 1 shows schematically the system used to attain backing-pump vacuum for removal of cyclohexane and for admission of gas for powder transfer. The milled hydride powder was then dried in vacuum for 1 hour and transferred under a N₂ atmosphere to a small cylindrical rubber tube. Powder transfer was carried out while the walls of the system and the isostatic tube were constantly tapped. This system also had a 100 mesh sieve which retained the milling balls and any coarse particles. The outer surface of the isostatic rubber tube was covered with a thin transparent flexible bag for added protection during and after transfer. The fine powder was aligned by pulsing three times in a 6 T magnetic field, pressed isostatically at a pressure of 200 MPa and then vacuum sintered for 1h at 1015-1060 °C, followed by cooling in the furnace. Magnetic characterization of the HD-sintered magnets was carried out using a permaemeter. Measurements were carried out after saturation in a pulsed field of 6 T. The density of the magnets was measured using a liquid displacement system.

3. Results and Discussion

The effects of milling time on the magnetic properties are shown in Figures 2-5 (all sintered at 1060 °C). The most striking feature in these graphs is the variation in remanence (B_r) and inductive coercivity (_bH_c) with milling time for both alloys. Pr₁₆Fe₇₆B₈ sintered permanent magnets made with powder milled for 18 hours exhibits an increase in remanence. Similarly, the Pr₁₇Fe₇₉B₄ HD sintered magnets also exhibit an increase in remanence, but only in those made from powders milled for significantly longer times. In both cases the remanence deteriorats when the powder is milled for prolonged times. The former shows a good value of remanence, 1.19 T and the latter, only 1.14 T. These values are consistent with the higher iron and reduced boron content in the Pr₁₇Fe₇₉B₄ alloy.

Pr₁₆Fe₇₆B₈ sintered permanent magnets made with powders milled for 18 and 27 hours exhibit a substantial increase in intrinsic coercivity (_iH_c). The best value of intrinsic coercivity can be observed in magnets made with powders milled for 27 hours, reaching almost 1.5 T. In a similar manner, the Pr₁₇Fe₇₉B₄ HD sintered magnets also exhibit an increase in intrinsic coercivity, but to a lesser extent, if prepared with powders milled for significantly longer milling times. In both cases this magnetic property deteriorates with powders milled for prolonged times. The former alloy showed a reasonable squareness factor (SF) value, of 0.78 and the latter, only 0.61. These values are also consistent with the higher amount of free iron and reduced amount of boron found in the Pr₁₇Fe₇₉B₄ alloy. A summary of the magnetic properties and densities (r) of the magnets prepared with these two alloys is given in Tables 1 and 2.

The effect of sintering temperature on the magnetic properties of the Pr₁₆Fe₇₆B₈ HD magnets is shown in Figures 6 and 7. Pr₁₆Fe₇₆B₈ sintered permanent magnets exhibit a marked increase in remanence when sintered at 1030 °C. Similarly, Pr₁₆Fe₇₆B₈ HD sintered magnets also exhibit an increase in the intrinsic coercivity, but when sintered at a slightly higher temperature (1045 °C). Both these properties deteriorate in magnets sintered at higher temperatures. Inductive coercivity increases steadily with sintering temperature in the HD powder, whereas the squareness factor reaches a peak at 1030 °C and, following the general behavior, deteriorates at higher temperatures. A summary of magnetic properties and density is given in Table 3.

4. Conclusions

Hydrogen decrepitated sintered permanent magnets have been successfully produced by the new low-cost laboratory technique. Sintered HD magnets based on Pr₁₆Fe₇₆B₈ exhibited a peak in remanence and coercivity when prepared with powders milled for shorter times compared to Pr₁₇Fe₇₉B₄ magnets. Optimum milling time for the powders of the former was 18 hours and for the latter, 27 hours. A permanent magnet produced from a powder milled for 20 hours and sintered at 1030 °C exhibited remanence of 1.23 T and intrinsic coercivity of 1.26 T.

Acknowledgments

The authors wish to thank FAPESP and IPEN-CNEN/SP for the financial support and infrastructure made available to carry out this investigation.

Received: November 23, 2003; Revised: December 28, 2004

• 1. Takiishi H, Lima LFCP, Faria RN, Powder Technology 2002; 127: 223-225.
• 2. Christodoulou CN, Schlup J, Hadjipanayis GC, J. Appl. Phys1987; 61(8): 3760-3763.
• 3. Ormerod J, J. Less-Common Metals. 1985; 111:49-57.
• 4. Withey PA, Magnetic and microstructural studies of Nd-Fe-B type alloys, [PhD Thesis], University of Birmingham. 1989; 92.
• 5. Faria RN, Abell JS, Harris IR, J. Alloys Comp 1991; 177:311-320.
• 6. Faria RN, Abell JS, Harris IR, J. Alloys Comp 1992; 185:81-88.
• 7. Faria RN, Williams AJ, Abell JS, Harris IR, Fourteenth International Workshop on Rare-Earth Magnets and Their Applications, 1996; São Paulo. p. 570-579.
• 8. Faria RN, Takiishi H, Lima LFCP, Costa I, J. Mag. Mag. Mat 2001; 237:263-268.
• 9. Faria RN, Castro ARM, Lima NB, J. Mag. Mag. Mat 2002; 238: 38-46.
• 10. Faria RN, J. Mag. Mag. Mat 2002; 238: 56-64.
• 11. Faria RN, Takiishi H, Castro ARM, Lima LFCP, Costa I, J. Mag. Mag. Mat 2002; 246: 351-359.

Publication Dates

• Publication in this collection
  06 Feb 2006
• Date of issue
  June 2005

History

• Accepted
  28 Dec 2004
• Received
  23 Nov 2003